宝马E-SYS单编模块教程
BMW E-SYS single compiled module tutorial
BMW programming and diagnostics (BMW engineers Programming / brush Hide / installation - programming, localization, single series, hidden) Tutorials:
item.taobao/item.htm?spm=a1z10.5.w4002-1388513814.12.Fr6U9
m&id=20107407001
宝马编程诊断(宝马工程师编程/刷隐藏/加装—编程，，单编，隐藏，)教程
item.taobao/item.htm?spm=a1z10.5.w4002-1388513814.12.Fr6U9m&id=20107407001
1: 电动电脑，首先将线 OBD口插到驾驶员左膝盖处，左下角（需用手指甲抠开有 OBD标志的盖板）
时注意一下 D型头的方向， X3 1系位于左脚处。 ENET线水晶头插到电脑， XP的本地连接 TCPIp
会自动获取地址；不踩刹车打开车子电源，不需要打开发动机，接好数据线之后(此时需耐心等待需
等一至二分钟自动寻本地网络地址，等没有了就连接成功了)，点软件连接标志
选最下面连 VIN，Target里选=F010，点连接；5系 GT与 5系一样选 F010注意此处 7系选 F01 1系、新 3选 F020 X3选 F025，点连接；不要选后面有 DIRECT的那个直接连接选项，根据 E-SYS
手册显示另有用处
First, adjust the language to U.S. English, senior there should tune. WIN7 still have to adjust.
1: Electric computer, first line into the OBD port pilots left knee, bottom left (required fingernail to pull open the cover with OBD logo) when the note D-head in the direction, X3 1 are located on left foot . ENET line crystal head into the computer, XP TCPIp local connection will automatically get address; does not turn on the car power brakes, no need to open the engine, connect the data cable after (this time must be patient to wait one to two minutes automatically find a local network addresses, and so there is no success on the connection), point software Connection logo
Select the bottom even VIN, Target in the election = F010, point connection;
5 Series and 5 Series GT F010 attention here as election election F01 1 series 7 series, the new three election F020 X3 election F025, point connection; Do not choose DIRECT behind that direct connectivity options, according to the E-SYS manual shows otherwise useless
2：显示连接成功.2: shows a successful connection
点 OK关闭对话框.,Click OK to close the dialog
3：按顺序点左边 Expert mode, Coding, 中间 Read，在展开的文件中右键 FA，选择
ActivateFA激活 FA 最后SVT
Actual栏中选择 READ VCM
3: Press the sequence point left Expert mode, Coding, middle Read, Right in the expanded file FA, select
ActivateFA activate FA last SVT Actual column select READ VCM
4：把左边 ECUS下面的文件夹比如 ACSM、CAS、CID、CMB_MEDIA前面的减号点一下，把这些模块都收起来，可以到 HU_CIC [63]，选中 CAFD_0000000这一项，点 READ Coding;
4: to the left ECUS following folders such as ACSM, CAS, CID, CMB_MEDIA tap the minus sign in front, put up all these modules, you can find HU_CIC [63], select CAFD_0000000 this one, point READ Coding;
5：进度条走完后，出现 REPORT-0 ERRORS 不要怕，这就是表明没错 OK，点 CLOSE
5: The progress bar has completed, the emergence REPORT-0 ERRORS Do not be afraid, this is the show that true OK, point CLOSE
宝马bmw就发现刚刚那个 CAFD_000000那一项变成文件夹了，点开这个文件夹，
如喜欢此软件请购买正版右键下一级的 CAFD_000000F9，点 EDIT FDL，输入 PIN码 2690 ，OK
如喜欢此软件请购买正版
如喜欢此软件请购买正版