12
2
2234
4
4
6
6
67
7
9
9
10
10
10
16
16
1620252529
3233343536373738394041424344
Table of Contents
Table of Contents EXTERIOR
PRECAUTIONS
PRECAUTIONS FOR SUPPLEMENTAL RESTRAINT SYSTEM (SRS) AIR BAG AND SEAT BELT P丰田yaris
RE-TENSIONER PRECAUTIONS NECESSARY FOR STEERING WHEEL ROTATION AFTER BATTERY DISCONNECTION PRECAUTIONS FOR PROCEDURE WITHOUT COWL TOP COVER PRECAUTIONS FOR WORK
PREPARATION
EX TERIOR
DESCRIPTION
COMPONENT PARTS ACTIVE GRILLE SHUTTER SYSTEM SYSTEM
ACTIVE GRILLE SHUTTER SYSTEM
WIRING DIAGRAM
ACTIVE GRILLE SHUTTER SYSTEM
SYMPTOM DIAGNOSIS
EX TERIOR
SQUEAK AND RATTLE TROUBLE DIAGNOSES
REMOVAL AND INSTALLATION
FRONT BUMPER W ITH FOG LAMP W ITHOUT FOG LAMP REAR BUMPER
W ITHOUT SONAR SYSTEM W ITH SONAR SYSTEM
FRONT GRILLE
ACTIVE GRILLE SHUTTER COWL TOP
FENDER PROTECTOR
REAR WHEEL HOUSE PROTECTOR FRONT UNDER COVER FLOOR UNDER COVER ROOF SIDE MOLDING
FRONT DOOR SASH COVER REAR DOOR SASH COVER
FRONT DOOR OUTSIDE MOLDING REAR DOOR OUTSIDE MOLDING REAR SPOILER EMBLEMS
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain types of collisions.
Information necessary to service the system safely is included in the “SRS AIR BAG” and “SEAT BELT” sections of this Service Manual.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
PRECAUTIONS NECESSARY FOR STEERING WHEEL ROTATION AFTER BATTERY DISCONNE
东风风行菱智m5ev
CTION : Precautions
RDE-001030480
For vehicle with steering lock unit, if the battery is disconnected or discharged, the steering wheel will lock and cannot be turned.
If turning the steering wheel is required with the battery disconnected or discharged, follow the operation procedure below before starting the repair operation. OPERATION PROCEDURE
1. Connect both battery cables.
起亚智跑报价及图片NOTE:
Supply power using jumper cables if battery is discharged.
2. Place the ignition switch in the ACC position.
(At this time, the steering lock will be released.)
3. Disconnect both battery cables. The steering lock will remain released with both battery cables disconnected and the steering wheel can be turned.
4. Perform the necessary repair operation.
5. When the repair work is completed, re-connect both battery cables. With the brake pedal released, place the ignition switch in the ON position, then in the LOCK position.
(The steering wheel will lock when the ignition switch is placed in the LOCK position.)
6. Perform self-diagnosis check of all control units using CONSULT.
Precautions
RDE-000960239 When performing the procedure after removing cowl top cover, cover the lower end
of windshield with urethane, etc.
RDE-000960239-01-IIB3706J
When removing or disassembling each component, be careful not to damage or deform it. If a component may be subject to interference, be sure to protect it with a shop cloth.
When removing (disengaging) components with a screwdriver or similar tool, be sure to wrap the component with a shop cloth or vinyl tape to protect it.
Protect the removed parts with a shop cloth and prevent them from being dropped.
Replace a deformed or damaged clip.
If a part is specified as a non-reusable part, always replace it with a new one.
Be sure to tighten bolts and nuts securely to the specified torque.
After installation is complete, be sure to check that each part works properly.
Follow the steps below to clean components:
Water soluble dirt:
1. Dip a soft cloth into lukewarm water, wring the water out of the cloth and wipe the dirty area.
2. Then rub with a soft, dry cloth.
半挂车倒车技巧图解Oily dirt:
1. Dip a soft cloth into lukewarm water with mild detergent (concentration: within 2 to 3%) and wipe the dirty area.
2. Then dip a cloth into fresh water, wring the water out of the cloth and wipe the detergent off.
3. Then rub with a soft, dry cloth.
Do not use organic solvent such as thinner, benzene, alcohol or gasoline.
秦plusdmiFor genuine leather seats, use a genuine leather seat cleaner.
Description
(TechMate No.)
Tool name
(J-39565)
Engine Ear
RDE-000960250-01-IIA0995E Locating the noise
(TechMate No.)
Tool name
Description
RDE-000960249 The actual shape of the tools may differ from those illustrated here.哈佛汽车h6
Tool number
(TechMate No.)
Tool name
Description
 —
(J-39570)
Chassis Ear
RDE-000960249-01-IIA0993E
Locating the noise
 —
(J-46534)
Trim Tool Set
RDE-000960249-02-WJIA0483
ZZ
Removing trim components