To release the seat-back from inside the trunk, pull the release under the trunk panel. Push the seat-back down, then let go of the release.
To lock the seat-back upright, push it firmly against the trunk panel. Make sure it is latched in place by pulling on the top of the seat.Make sure that the folded seat-back
does not interfere with the front
passenger’s seat-back. This will
cause the front passenger’s weight
sensors to work improperly (see
page ). Also check the passenger
airbag off indicator to assure proper
operation of the passenger’s
advanced front airbag.
Do not put any heavy items on the
seat-back when it is folded down.
Make sure all items in the trunk, or
items extending through the opening
into the back seat, are secured.
Loose items can fly forward and
cause injury if you have to brake
hard. See on page
.
Never drive with the seat-back
folded down and the trunk lid open.
See on
page.
Make sure all rear shoulder belts are
positioned in front of the rear seat-
back,and the center shoulder belt is
re-positioned in the guide whenever
the seat-back is in its upright position.
Be sure the center shoulder belt is
not twisted.
50
25
193
Seats
Carrying Cargo
Carbon Monoxide Hazard
Instruments
and
Controls
Follow these precautions whenever you use the seat heaters:
Use the HI setting only to heat the seats quickly,because it draws large amounts of current from the battery.
If the engine is left idling for an extended period,do not use the seat heaters,even on the LO
setting.It can weaken the battery,causing hard starting.
Both front seats are equipped with seat heaters.The passenger seat only has heaters in the seat bottom because of the side airbag system.The ignition switch must be in the ON (II)position to use the heaters.
Push the front of the switch,HI,to rapidly heat up the seat.After the seat reaches a comfortable
temperature,select LO by pushing the back of the switch.This will keep the seat warm.
In HI,the heater turns off when the seat gets warm,and turns back on after the seat’s temperature drops.In LO,the heater runs continuously.It does not cycle with temperature changes.
On EX-L and EX-V6models
Seat Heaters
CONTINUED Turn the ignition switch to the ON
(II)position to raise or lower either
window.To open the window,push
the switch down and hold it.Release
the switch when you want the
window to stop.Pull back on the
switch and hold it to close the
window.
The windows operate for up to10
minutes after you turn off the
ignition switch.Opening either door
cancels this function.
To open or close the
driver’s window,push or pull the
window switch firmly down or up to
the second detent,and release it.
The window will automatically go
down or up all the way.To stop the
window,pull or push the window
switch briefly.
Power Windows
AUTO
Instruments
and
Controls
Press the UNLOCK button once to unlock the driver’s door.Press the UNLOCK button a second time,and hold it.The passenger’s door unlocks,and both windows start to open.To stop the windows,release the button.
You can open both windows from the outside with the remote transmitter.Auto reverse stops sensing when the window is almost closed.You should always check that all passengers and objects are away from the window before closing it.
To open the windows further,press the button again (within 10seconds).
You cannot close the windows with the remote transmitter.
If the driver’s window senses any obstacle while it is closing automatically,it will
reverse direction,and then stop.To close the window,remove the
obstacle,then use the window switch again.
If your vehicle’s battery is
disconnected or goes dead,or the driver’s window fuse is removed,the AUTO function may be disabled.If the AUTO function is disabled,the power window system will need to be reset after reconnecting the battery or installing the fuse.
If the power windows do not operate properly after resetting,have your vehicle checked by your dealer.
Start the engine.Push down and hold the driver’s window switch until the window is fully open.Pull and hold the driver’s window switch to close the window
completely,then hold the switch for about 2seconds.
1.2. 1.2.3.Power Windows
Opening the Windows with the Remote Transmitter
AUTO REVERSE
You can open and close the windows with the key in the driver’s door lock.
lock.
Turn the key counterclockwise,
then release it.
Turn the key counterclockwise
again,and hold it.Both windows
start to close.To stop the windows,
release the key.
To close the windows further,turn
and hold the key again(within
10seconds).
NOTE:If the windows stop before
the desired position,repeat steps2
and3.
Insert the key in the driver’s door
lock.
Turn the key clockwise,then
release it.
Turn the key clockwise again,and
hold it.Both windows start to open.
To stop the windows,release the
key.
To open the windows further,turn
and hold the key again(within
10seconds).
NOTE:If the windows stop before
the desired position,repeat steps2
and3.
To open:To close:
1.
2.
3.
4.
3.
4.
1.
2.
Opening/Closing the Windows with the Key Power Windows
Instruments
and
Controls
发布评论