Gentex by VOXX Corporation
Installation Instructions
Bezelled
ADVGEN45A4
Bezelled w/ Homelink
ADVGEN80EXP
ADVGEN45A4PW4
ADVGEN40A4
Frameless
ADVGEN8EXP
Frameless w/ Homelink
ADVGEN85EXP
捷豹路虎ADVGEN45AB5
TOOLS REQUIRED:
Safety Glasses Utility Knife Pliers #2 Phillip's Screwdriver Clean Rag Electrical Tape 4mm Flat Screwdriver Flashlight
DC Voltmeter Fish-Wire (Coat Hanger) #T20 Torx Driver Panel Removal Tool
Perform the following pre-installation steps:
1. Place kit components on a clean, padded surface.
2. Record your programmed radio stations.
3. Remove driver side scuff plate. (Fig. 1)
4. Remove driver side door seal. (Fig. 2)
5. Remove driver side kick plate / cowl cover. (Fig. 3)
6. Remove driver side grab handle if equipped. (Fig. 4)
7. Remove driver side A-pillar trim. (Fig. 5) INSTALLATION PRECAUTIONS / NOTES:
➢ Do not use excessive force when removing OEM mirror from windshield.
➢ Do not push fish-wire too far into dash to avoid damage to existing components. ➢ Do not place wire harness against objects with sharp edges that may cause electrical shorting. ➢ On vehicles equipped with A-pillar (side impact or SRS) airbags, verify mirror harness path remains
clear of airbag. Harness should follow and be secured to, existing OEM wiring with tie wraps.
➢ Verify that auto-dimming mirror harnesses do not interfere with brake, clutch, emergency brake or air bag
operation. Use tie wraps to bundle and secure wiring away from critical locations. 1 Preparation 1
2
3
4
5
8. Remove OEM mirror. (Fig. 6,7 or 8)
a) Loosen #T20 torx screw on mirror mount and slide mirror
upwards off from windshield button. (Fig. 6)
- - OR - -
奇瑞qq3论坛b) Insert 4mm into opening at bottom of mirror mount to disengage locking tab and slide mirror upwards off from windshield button.
NOTE: Gently wiggling mirror while sliding upwards will assist removal. - - OR - -
c) Insert panel removal tool into opening at bottom of mirror mount to disengage locking tab and
slide mirror upwards off from windshield button.
(Fig. 8)
NOTE: Gently wiggling mirror while sliding upwards will assist removal.
1. Attach auto-dimming mirror.
a) Hold the mirror and slide the mirror downwards over wind-shield
button until fully seated. (Fig. 9)
b) Using #T20 torx driver, tighten the mirror mounting bracket
screw to 1.3 ft-lbs (17.8 kg-cm). DO NOT OVERTIGHTEN
NOTE: You will need to find a supply wire in your vehicle that provides +12V when vehicle is running or the key is in the ON or ACC
position. You will also need to find a supply wire that provides +12V constant power when vehicle is both ON and OFF. Your automotive repair shop may sometimes be able to advise readily
available locations for connecting to these power sources.
A TIP: The cigarette lighter or power port receptacle may be a source of
switched +12V or constant +12V, depending on vehicle make.
消防车转弯半径1. Locate ignition (+12V switched) wire.
a) Using a multi-meter, find a wire exiting the fuse block or junction block that tests +12V and is controlled by the ignition switch.
Operate vehicle accessories (power windows, door locks, power
mirrors, etc.) to ensure that voltage does not drop on this wire. (Fig. 10)
b) Ensure power in this wire is off when vehicle key is OFF and label wire "IGNITION."
2 Auto-Dimming Mirror Installation CAUTION ! Do not use excessive force. Damage to windshield could occur.
3 Route Auto-Dimming Mirror Harness to Vehicle Power 1.3 ft-lbs
CAUTION
!
6
8
9
10
奥迪s8报价及图片7
CAUTION
!
2. Locate constant power (+12V constant) wire.
a) Using a multi-meter, find a wire exiting the fuse block that tests
+12V with vehicle ignition in the ACC, ON and OFF positions.
(Fig. 11)
b) Ensure power in this wire is still present when vehicle key is
OFF and label wire "CONSTANT."
3. Disconnect vehicle's negative battery terminal. (Fig. 12)
4. Plug auto-dimming mirror harness into back of mirror. (Fig. 13)
5. Route harness up to vehicle headliner. (Fig. 14)
a) Install optional wire cover (if purchased). (Fig. 15)
6. Route haress across vehicle headliner to top of A-pillar on side of vehicle where vehicle connection wires / fuse block were found.
a) Use panel removal tool to ensure harness is tucked between
headliner and roof of vehicle. (Fig. 16)11
12
13
14
15
16
7. Route harness down A-pillar. (Fig. 17)
NOTE: Harness will be secured later in installation procedure.
8. Route harness to vehicle connection wires.
a) Using fish-wire, route harness from base of A-pillar through dash
and into connection wire / fuse block area. (Fig. 18)
9. Attach wire tap to vehicle wire marked IGNITION.
a) Center blade of wire tap on IGNITION wire and close wire tap
with pliers. (Fig. 19)
b) Ensure both halves of wire tap are closed completely and
locking tab is engaged.
10. Connect auto-dimming mirror harness switched power wire to
vehicle wire marked IGNITION.
a) Locate the harness wire with WHITE STRIPE.
b) Insert spade terminal on WHITE STRIPE wire into the wire tap
on the vehicle wire labeled IGNITION. (Fig. 20)
11. Attach wire tap to vehicle wire marked CONSTANT.
a) Center blade of wire tap on CONSTANT wire and close wire tap
with pliers. (Fig. 21)
b) Ensure both halves of wire tap are closed completely and
locking tab is engaged.
12. Connect auto-dimming mirror harness constant power wire to
vehicle wire marked CONSTANT.
a) Locate the SOLID BLACK harness wire with spade terminal.
b) Insert spade terminal on SOLID BLACK wire into the wire tap
on the vehicle wire labeled CONSTANT. (Fig. 22)19 22 21 20 18 17
发布评论