XXX Rear-XXX Project
XXX:
1.The n time is 30 minutes (excluding XXX);
丰田自动变速器2. is 100 points。with each project worth 1 point。There are a total of 53 disassembly and assembly projects。for a total of 53 points;
3.Each two XXX.
Class Name Student ID Q&A Score
Step Project XXX
Disassembly of Toyota A341E Rear-XXX
1.Disassemble the automatic n
1.Loosen the six 12mm bolts of the oil pump;
2.Loosen the four 14mm and two 17mm bolts of the upper end housing of the automatic n;
3.Remove the housing and place it upside down on the ground;
2.Disassemble the oil pump
1.Loosen the six 12mm bolts of the oil pump。
2.Remove the oil pump;
3.Disassemble the overdrive clutch
1.Remove the overdrive clutch C0;
2.XXX;
4.Disassemble the overdrive brake
1.Remove the overdrive brake B0 drum;
2.Disassemble the brake B0 and overdrive ring gear;
5.Disassemble clutch C1
1.Remove clutch C1;
6.Disassemble clutch C2
1.Remove clutch C2;
7.Flip the table
1.Flip the XXX and the oil pan is facing up;
8.Disassemble the lower end of the automatic n
1.Loosen the bolt of the first speed sensor;
2.Loosen the bolt of the second speed sensor;
3.Loosen the six 12mm bolts of the lower end housing of the automatic n (two of which are shorter and four are longer);
4.Remove the lower end housing of the automatic n and place it upside down on the ground;
10.Remove the first snap ring
1.Use snap ring pliers to remove the first snap ring;
11.Remove the driven gear of the speedometer
1.Remove the driven gear of the speedometer;
2.Use a screwdriver to remove the steel ball;
12.Remove the speed sensor
1.Remove the speed sensor n rotor;
2.Remove the half-circle pin;
13.Remove the second snap ring
1.Use snap ring pliers to remove the second snap ring;
14.Remove the oil pan
1.Remove the 10mm bolt of the oil pan diagonally;
2.Remove the oil pan and place the disassembled bolts in the oil pan;
15.Remove the oil line
1.Remove the oil line (disassembly sequence: 1 short。1 medium。1 long。1 Z-shaped);
2.Place the disassembled oil line in the oil pan;
16.XXX
1.XXX;
17.Disassemble the valve body filter
1.Loosen the six 8mm bolts of the valve body filter;
2.Remove the valve body filter;
1.Loosen the bolts of the valve body first until the XXX。and then
18.Disassemble the XXX.
1.使用螺丝刀将节气门阀卡紧，从凸轮的侧面拆下节气门拉索钢索；
2.取下阀体；
3.翻转自动变速器台架，使其竖直，上端向上；
4.拧出制动器B1、B2的两颗12号螺栓，取出制动器B1、B2总成；
5.拆下卡环；
6.抽出前后排行星齿轮总成，拿出制动器B3传动挡圈和轴承；
7.用卡环钳拆开后排行星架的齿圈，拆下前排行星架和后输入轴与前排行星齿圈总成，取出轴承；
8.将输出轴与前排行星齿圈结合，放入轴承；
9.安装前排行星架，用卡环钳安装后排行星齿圈，装上后排行星架和单向离合器F2总成；
发布评论